LAN without netbios
This page was pulled into the static site from the original vBulletin thread — rescued from the Internet Archive or the vBulletin backup database after the forum upgrade made the live threads unreachable; original authorship is credited below.
i wanna install a small lan at home
Win98SE
WinME
winME
Win98
but i cant seem to install netbios properly....i cant find it in my win98SE machine
a friend told that i need not use netbios . i could also use tcp/ip for filesharing and printer sharing ......he told me to disable dhcp and set static ip for each machine and enable file and printer sharing and i will be able to do the sharing
is that possible?
thanx
Discussion replies
— 2002-03-08
one more thing to point out
my printer does not have a NIC and i have a 4 port linksys router
so i will not be able to set a static ip for my printer.so is print sharing still possible in this case?
thanx
Magickian — 2002-03-08
NetBIOS is the protocol that Microsoft uses for its local network communication, when you install the TCP/IP drivers it is installed with them by default (these are tcp/udp ports 137, 138, and 139). You can see if NetBIOS is enabled by going into Control Panel, double click on Network, click TCP/IP, go to Properties, then click the NetBIOS tab. NetBEUI is most likely what you're referring to as not being able to install. NetBEUI is basically a simple way to install NetBIOS on a local network, but you're only limited to the computers on the same class subnet as you (otherwise known as "non-routable").
You will probably be better off using NetBEUI for setting up your file and print sharing as it's simple to use as long as you know each computer's name. To set up NetBEUI, open the the Network icon under Control Panel. Click the File and Print Sharing button and check "I want to allow others access to my whatever." Click ok, then go to Add, then Protocol, then Microsoft, then choose NetBEUI. It'll do some junk, probably including asking for the cd, then just tell it ok, and reboot when it tells you to.
Once you're rebooted, test out your sharing. Share your hard drive or a folder (done by right clicking on the folder and going to "Sharing") and make sure all computers are able to see it and access it, then you're ready to go. If a computer is not sharing anything, it may not appear in network neighborhood, which is why I suggest sharing from each computer, make sure to disable any shares that you don't need though.
To share your printer, go to the Printers folder (located under Start, Settings, Printers). Right click on the printer and choose sharing (think there's a sharing option for printers anyway heh). Next, go to another computer and go to the Printers folder, go to Add Printer, then choose Network Printer. If the printer is not listed, try directly accessing it by doing:
\\computername\printername (replacing computername with whatever the computer's name is, and printername with whatever you shared the printer as)
Then you may need to install the drivers for the printer on that machine and you should be good to go after that. You'll have to follow these steps with or without NetBEUI, but you may run into issues where you cannot contact the computer, or other such crap because NetBIOS over TCP/IP can be a female dog sometimes.
— 2002-03-08
the netbios is not there......i recently uninstalled my NIC and i think i may have accidentally removed it along with
The Helper — 2002-03-09
Have you resolved your problem? If you are still having problems post back and let us know and we will do our best to try and help you resolve them.
Best Regards
lucky — 2002-03-09
nopezzz...i still cant solve it...ok
i'll describe my situation to u guys
for certain reasons i cant install tcp/ip onto my com
(and in the first place its not there....its not on the network properties) i think i removed it along wif my NIC when i did a format and cos i lost my win98 CD the time i reinstalled my NIC
and now i cant be connected to my small lan at home
and a friend recently told me that i could use tcp/ip to do file sharing and printer sharing...and all i had to do was set static ip
i didn't really catch wat he meant.....and i dunno if its really possible. so is there anyway to solve my problem and can i really use tcp/ip for file and print sharing?
thanx
Talahar — 2002-03-10
I operate a home LAN utilising Win ME home networking and Internet Connection sharing. It's friendly and easy to set up. If you have ME use it and create a home networking disk. Now if only I could stop my little boy going hostile on me when we play Diablo 2 on the network!
— 2002-03-11
well.......the main problem is that i cant find my discS
and i would also like to aquire the knowledge of setting up a lan vis tcp/ip
Talahar — 2002-03-11
Have you even tried home networking via ME? As you appear to have it installed on 2 pcs give it a try. You can mull over the settings once it's set up.
lucky — 2002-03-11
ummm....i HAD a lan working and its now down bcos i removed the netbios accidentally...and i dun think i wanna change my systems to ME and i lost the CD anways
thanx
The Helper — 2002-03-11
You should always copy all the .cab files off of the CDs into a folder on your hard disk, that way when you need to install stuff you can just point your installation program at that folder instead of the CD. If you had it on your computer you should look for any .cab files on your computer, maybe someone did that (if you bought your computer from Best Buy or something). Also, try reinstalling and when it asks for files put it in your Windows folders, it might find the old files and be able to use them in your installation.
lucky — 2002-03-12
mmm.....but i lost the disc
anyways i really wanna know if i can use tcp/ip to do sharing
but i cant seem to find resources on it
thanx
Tutorials submitted by users are copyright of the original author. All other content on this site is copyright TheHelper.net.
Copyright is secured automatically upon creation, and does not require registration